Home > Error Code > F10 Error On Frigidaire Oven

F10 Error On Frigidaire Oven

Contents

If the reading is correct, the EOC would need to be replaced. Otherwise the EOC is the culprit. Also the broiler coil came on but the unit was not in broil but bake. If the sensor is not reading correctly make sure you have hooked up the meter to the sensor the right way. http://ascadys.net/error-code/f1-error-on-frigidaire-oven.html

Press START to accept the temperature change and the display will return to the time of day. George sharon // Jan 1, 2015 at 10:09 pm i have a frigidaire model fgef301dnb. Appliance Princess 4,631 views 2:35 How to Fix an F1 Error On a Kenmore or GE Range - Duration: 11:41. Set the rotary dial to the lowest ohms of resistance setting, pinch the probes together and rotate the knurled adjusting wheel on the side of the instrument until the needle reads

F10 Error On Frigidaire Oven

Otherwise the EOC is the culprit. If the error code returns, the EOC would need to be replaced. At the same time make sure the wire harness from the probe to the control panel is not damaged. A reading between 1,000 and 1,100 ohms suggests that the sensor is working.

Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to Found a site where guy said check all the purple wires since the wiring is colored coded. Thank you for your question. Kenmore Gas Oven F10 Error Code Gene.

Then ordered a new OCR from Amazon and that didn't help. Gene // Dec 18, 2014 at 7:58 pm Hello Jim, Sorry for the delay. Rating is available when the video has been rented.

What is the part number of the new EOC and where did you get from?

I ran the self clean on my electrolux and within 2 weeks of using my oven again, I had the F10 runaway temperature alarm. Kenmore Electronic Oven Control Keep me posted. Did the motor run or not? With this info.

Kenmore Oven F10 Error Beeping

If that checks good, then your control board is the problem. http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Range-Parts/Repair-Maintenance/Questions-Answers/f10-fault-code-on-kenmore-oven/Model-79096112407/0582/0124111/214929?modelNumber=79096112407 Thank you, Gene. F10 Error On Frigidaire Oven The part number for the temperature probe is 316217002 The part number for the EOC is 318414213 Good luck. What Does F10 Mean On A Frigidaire Oven Mike // Jun 6, 2015 at 7:05 pm Hi Gene, I have a PLES389ECE showing F30.

The black potentiometer should have a resistance of 10KΩ (± 10%). this content For now, I guess I'll remove all remnant melted plastic from the connectors to rule out a short inside that molten mess. Good luck. Q: What is the reason why the pilot light will not stay lit? Kenmore Oven F10 Reset

Now it wont let me set the clock to the right time. If disconnecting the power for a few minutes does not help, the EOC (electronic oven control) may need to be replaced. Follow these steps to replace the EOC: Unplug the range. Remove the rear You may want to order a new overlay if you would not be able to move the old one to the new EOC. http://ascadys.net/error-code/f11-error-code-on-frigidaire-oven.html Gene.

Ask a question Get up to 55 % off On Washers Related Questions Related Questions'>What does F10 error code mean on my Kenmore electric range, model 79094002600? 1 answer Related Questions'>kenmore What Does F10 Mean On A Kenmore Oven Sounds like the EOC has gone bad again. I checked the RTD temperature probe at the plastic connector (1083 - 1100 ohms).

Check your oven sensor probe connection as well: Here's the oven sensor probe for your model: Part#316217001 Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech.

I was wondering if there is anything that I can test or diagnose from the front, without pulling the oven out from the wall? RepairClinic.com 98,072 views 3:44 Replacing a Worm Gear in a Stand Mixer - Duration: 2:50. it started to throw a f10 code after about 15min on bake and wont stop beeping until I unplug it..ive noticed the element will stay glowing red even when the oven Kenmore Glass Top Stove Error Code F10 the stove was not in use at the time and it just started beeping and showing code.

Kevin Foster // Jun 6, 2014 at 6:47 am Good day, Gene I have a Frigidaire Electric Range Model #GLEF379DBK The other night my range just started beeping all of a Thanks for any and all help! But it would not hurt if you will eliminate those plugs and splice the wires using a high temperature porcelain wire nuts. check over here Thank you for your question.

Everything works fine. The connection is easily seen. After several power-cycles with the same error, I came to your page. Other factors includ...

Thank you for your question. if the resistance through the circuit is normal (1100 ohms or the same resistance as measured at the probe) then the electronic control board (part 316557108) will likely need to be I was able to use it a couple times after but the cooking times varied between a little slow and A LOT slow.