Home > Juniper Error > Juniper Error Device Ae0 Not Found

Juniper Error Device Ae0 Not Found

The 802.3ad standard is known as Link Aggregation Control Protocol (LACP). Any form of reproduction, > > dissemination, copying, disclosure, modification, > distribution and / or publication of this > > message without the prior written consent of the > author of Here was my configuration: [email protected]# show interfaces ae1 aggregated-ether-options { minimum-links 1; link-speed 10g; lacp { passive; periodic fast; } } unit 0 { description lab-mx1-ae1; family ethernet-switching { port-mode trunk; Be Sociable, Share! http://ascadys.net/juniper-error/juniper-error-insertion-point-not-found.html

Saved me lots of time. If you have received this email in error > please delete it and notify the sender > > immediately. As you are getting an error on the show command I am wondering if this step was left out. All rights reserved. https://forums.juniper.net/t5/Ethernet-Switching/ae-interface-missing-on-EX4500/td-p/86430

There are a few proprietary standards for aggregating ethernet links, but Juniper uses the IEEE 802.3ad standard and Cisco can also be configured to use this. Since you're using ae0 the device count should be set to 1 as you've done. Contact Gossamer Threads Web Applications & Managed Hosting Powered by Gossamer Threads Inc. HTHs..

System Engineer / Network Administrator View all posts by Kaven G. → Post navigation ← Windows : Shared printer exist but not shown in Devices and Printers Linux : MySQL InnoDB: Error Device ae1 Not Found I recently ran into a problem on an EX series switch - after already setting interfaces ae0 ae1 and ae2 up. set chassis aggregated-devices ethernet device-count 100 I set this to 100 because I did not see any use in having to add more interfaces to this later on. If you try to watch statistic (LACP) can see error: device ae1 not found in Juniper.

Message 1 of 3 (10,905 Views)   Everyone's Tags: 11.1ae0Errorex4500JUNOS View All (5) Reply muttbarker Distinguished Expert Posts: 2,408 Registered: ‎01-29-2008 1 Kudo Re: ae interface missing on EX4500 Options Mark Rich is currently JNCIA-JUNOS certified and has previously held several other certifications from Juniper, Cisco, Checkpoint and Microsoft. http://new.mail.yahoo.com Previous message: [j-nsp] Configuring aggregate link/lacp in juniper M160 Next message: [j-nsp] Subject: Graceful restart & Graceful switchover Messages sorted by: [ date ] [ thread ] [ subject ] Before opening any mail and attachments > please check them for viruses and > > defect. > _______________________________________________ > juniper-nsp mailing list juniper-nsp at puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp > ____________________________________________________________________________________ Do you

not the network my blog about data networking and cisco certification Skip to content Homeaboutnetworking books Junos Basics - Aggregated Ethernet Interfaces (LACP) By Rich Bibby | July 29, 2013 3 Any views or opinions presented in this > email are solely those of the author and > > may not necessarily reflect the opinions of HCL or > its affiliates. key can't be retrieved. Go to Solution.

Thanks so much for the walk-through. https://www.nertwork.com/tag/juniper/ of 32 per physical chassis unit) : Command Shell set chassis aggregated-devices ethernet device-count 1 1 set chassis aggregated-devices ethernet device-count 1 Commit the changes and the LACP interface should now appear Here's a quick test to show the dependancy: [edit] root at Phanlanx# show interfaces ae0 { aggregated-ether-options { lacp { active; } } unit 0 { family inet { address 20.1.1.1/24; Message 2 of 3 (10,901 Views)   Reply monodactylus Contributor Posts: 23 Registered: ‎03-07-2010 0 Kudos Re: ae interface missing on EX4500 Options Mark as New Bookmark Subscribe Subscribe to RSS

set chassis aggregated-devices ethernet device-count 100 I set this to 100 because I did not see any use in having to add more interfaces to this later on. navigate here Rich Follow Rich on Twitter Category: How to guides Juniper Tags: juniper, junos About Rich Bibby Rich Bibby is a Network Engineer with extensive experience in designing, deploying and supporting enterprise networks I needed to allow a certain amount of aggregate devices. From Cisco side was written (Gi0/2 suspended: LACP currently not enabled on the remote port) - on remote port doesn't set up.  [email protected]> show lacp interfaces ae1 error: device ae1 not

Skip to content HomeAboutToolsContact JunOS : error: device ae0 not found By Kaven G. | July 19, 2014 0 Comment Having problem setting LACP interface on JunOS and got this "error: Author James FarrPosted on November 4, 2014April 23, 2016Format ImageCategories Juniper, Major VendorsTags 4300, Juniper, PortmapLeave a comment on Juniper 4300 Portmap What is Software Defined Networking or SDN? A kudo would be cool if you think I earned it. Check This Out Nertwork Networking Blog - For Juniper JUNOS - Cisco IOS - and Cumulus Linux Proudly powered by WordPress Skip to content IT Stickers IT заметки Menu and widgets Search for: Recent

Search for: Search Sponsored Links Recent Posts Grow LVM (Ubuntu) KVM April 23, 2016 FTOS Dell LLDP System Name February 3, 2015 Change Linux (Cumulus) IP address without losing connectivity January Reply ↓ Leave a Reply Cancel reply Your email address will not be published. Has anyone come across this in Junos11.1R1.10?Thanks,Will Solved!

Reply ↓ Rich Bibby Post authorAugust 25, 2014 Thanks Angad Reply ↓ mike March 14, 2016 Completely spot on.

I can't wait until we get our hands on some of the SDN gear! Jared --- "Sundaresan Rajangam - TLS , Chennai" wrote: > Hello All > > > > I was not successful in configuring aggregate > link in juniper M160. Subject User Time LACP / 802.3ad interop with Cisco 6500 Andrew.McConnell at sungard Aug 28, 2004, 1:34 AM LACP / 802.3ad interop with Cisco 6500 jeff at reflected Aug 28, 2004, 3:44 AM DreamHost Uses SDN Cisco Open Network Environment - Cisco Systems.

All rights reserved Log in | How to Buy | Contact Us | United States(Change) Choose Country North America United States Europe Deutschland - Germany España - Spain France Italia For a detailed explanation of the output see this article from Juniper, but suffice to say the Mux State of Collecting and Distributing means the LACP protocol is working correctly. We'll make the Juniper side Active, so that it initiates the transmissison of LACP packets: set interfaces ae0 aggregated-ether-options lacp active Finally, we need to set the aggregated link to be this contact form JunOS : Alarm Management Ethernet Link Down Linux : Change installation and boot video resolution on CentOS/RHEL 7 Archives Archives Select Month November 2016 October 2016 September 2016 August 2016 July

We can also confirm the trunk is up and trunking for VLAN's 100 and 200: [email protected]> show ethernet-switching interfaces Interface State VLAN members Tag Tagging Blocking ae0.0 up IT 200 tagged When you define an aggregated ethernet I/F you must first created it logically by setting the following:[email protected]# set chassis aggregated-devices ethernet device-count X