Home > Juniper Error > Juniper Error Statistics

Juniper Error Statistics

Interface has a TX buffer for outgoing traffic, when the rate of traffic pushed to this buffer (could be DMA or CPU) is too high the interface cannot handle the amount On the TX Matrix Plus router, display statistics about PFE traffic for all its attached routersfpc slot—(T Series and M320 routers only) (Optional) Display statistics for a Flexible PIC Concentrator (FPC) Contact Juniper Support Submit DynamicBooks i Add Multiple Topics to DynamicBooks Add Current Topic to DynamicBooks Check for Fast Ethernet or Gigabit Ethernet Interface Error StatisticsPurposePersistent interface error statistics indicate that Contact Juniper Support Submit DynamicBooks i Add Multiple Topics to DynamicBooks Add Current Topic to DynamicBooks  Related DocumentationEX Seriesclear interfaces statisticsM Seriesclear interfaces statisticsMX Seriesclear interfaces statisticsPTX Seriesclear interfaces statisticsSRX Seriesclear Check This Out

If there are any persistent input or output errors, open a case with the Juniper Networks Technical Assistance Center (JTAC) at [email protected], or at 1-888-314-JTAC (within the United States) or 1-408-745-9500 The hardware counters provide information on the general firewall behavior, and the flow counters provide information on the number of packets inspected at the flow level. Thank You! The PC interface is used to fetch the boot string from the routing engine while the PIC boot up in an idle situation is used to send keep alive or health

Otherwise, replace slot with a value from 0 through 31.On a TX Matrix Plus router, if you specify the number of a T1600 router by using the lcc number option (the DynamicBook 0 Select All Add Topics To DynamicBook Rate and give feedback: X This document helped resolve my issue Yes No Additional Comments 800 characters remaining May we contact you if For example, the following commands have the same result:[email protected]> show pfe statistics error fpc 1 lcc [email protected]> show pfe statistics error fpc 9lcc number—(TX Matrix and TX Matrix Plus routers only)

Packets are dropped silently but are also sent to the Routing Engine for further processing. LU Chip 2 LUCHIP(8) ISTAT PIO Errors: None recorded. All rights reserved. Thank You!

As a result, the output of the show pfe statistics traffic command shows extra packets. Name: E-mail: Enter a valid Email ID Need product assistance? All rights reserved Previous Page Next Page Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security Name: E-mail: Enter a valid Email ID Need product assistance?

The hardware counters provide information on hardware performance.To view and interpret hardware reports, perform the following steps using the WebUI or CLI:WebUI Open the WebUI. Thank You! If you issue the clear interfaces statistics interface-name command and then perform a graceful Routing Engine switchover, the interface statistics are not cleared on the new master. If there are any persistent input or output errors, open a case with the Juniper Networks Technical Assistance Center (JTAC) at [email protected], or at 1-888-314-JTAC (within the United States) or 1-408-745-9500

Thank You! All rights reserved Previous Page Next Page Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security DynamicBook 0 Select All Add Topics To DynamicBook Rate and give feedback: X This document helped resolve my issue Yes No Additional Comments 800 characters remaining May we contact you if For information about the input errors and output errors, see Fast Ethernet and Gigabit Ethernet Counters.Sample Outputshow interfaces statistics (Fast Ethernet)[email protected]> show interfaces fe-1/3/1 statisticsPhysical interface: fe-1/3/1, Enabled, Physical link is Up

All rights reserved Previous Page Next Page Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security his comment is here On a TX Matrix Plus router, display statistics for a specific router (or line-card chassis) that is connected to the TX Matrix Plus router.Replace number with the following values depending on Otherwise, replace slot with a value from 0 through 31. For more information on accessing the WebUI, go to KB4060 - Accessing Your NetScreen, SSG, or ISG Firewall Using the WebUI From the ScreenOS options menu, click Reports, select Counters,

Packets that match a new session are retried, whereas packets that match an existing session are not.No tunnel foundThe packet was dropped because a valid tunnel could not be foundNo session Contact Juniper Support Submit DynamicBooks i Add Multiple Topics to DynamicBooks Add Current Topic to DynamicBooks clear interfaces statistics Syntax clear interfaces statistics (all | interface-name) Release Information Command introduced before Required Privilege Level clear List of Sample Output clear interfaces statistics Output Fields When you enter this command, you are provided feedback on the status of your request. this contact form This counter is used when too many packets hit the interface for it to process at that time.

All rights reserved Previous Page Next Page Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security Packets that match a new session are retried, whereas packets that match an existing session are not.It pretty much explains itself I suppose!:http://juniper.ie/techpubs/software/junos-security/junos-security10.2/junos-security-cli-reference/i... Transit statisticsNumber of packets and bytes transiting the physical interface.Flow input statisticsStatistics on packets received by flow module.Flow output statisticsStatistics on packets sent by flow module.Flow error statisticsPacket drop statistics for

There should not be any input or output errors.

Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security Software Defined Networking Switches All Products A-Z Contact Juniper Support Submit DynamicBooks i Add Multiple Topics to DynamicBooks Add Current Topic to DynamicBooks  Related DocumentationEX Seriesshow pfe statistics trafficshow pfe statistics bridgeM Seriesshow pfe statistics trafficMX Seriesshow pfe All rights reserved Previous Page Next Page Back Products & Services Products & Services Products Identity and Policy Control Network Edge Services Network Management Network Operating System Packet Optical Routers Security See EX8208 Switch Hardware and CLI Terminology Mapping or EX8216 Switch Hardware and CLI Terminology Mapping.Required Privilege Leveladmin Related DocumentationEX Seriesshow pfe statistics bridgeshow pfe statistics errorM Seriesshow pfe statistics errorMX Seriesshow

Following is a list of typical interface names. Extended discards are reported when packets match a firewall filter term that has an action of discard and an additional action that requires Routing Engine processing, such as log, count, sample, Replace pim with the PIM slot and port with the port number. navigate here Minor sessions are allocated for storing additional TCP state information.No more sessionsThe packet was dropped because there were no more free sessions available.No route presentThe packet was dropped because a valid

The session is rerouted, and this reroute could fail because:A new route could not be found; either the previous route was removed, or the route was changed to discard or reject.Multiple All rights reserved Previous Page Next Page Log in | How to Buy | Contact Us | United States(Change) Choose Country North America United States Europe Deutschland - Germany España - Of these packets, 40007 pps that need to undergo UHP are looped back for label de-capsulation. DynamicBook 0 Select All Add Topics To DynamicBook Rate and give feedback: X This document helped resolve my issue Yes No Additional Comments 800 characters remaining May we contact you if

Packets are dropped.in packetsNumber of packets receivedin short frameNumber of incoming packets with an Ethernet frame shorter than 64 bytes (including the frame checksum)out underrunNumber of transmitted underrun packets.