Home > Konica Error > Konica Error Code Sc49-01

Konica Error Code Sc49-01

Please try the request again. When M16 turns ON from OFF, the blowout of ICP abnormality is detected with a 24V down signal normal. SC23-06 It is checked that the movement of the blade motor (M14) is not completed. SC28-02 A transfer leak is detected. check over here

HP OfficeJet 7410 All-In-One... 14 Answers Cannot delete print job HP PSC 1315 All-In-One InkJet... 13 Answers Konica Minolta Admin Password Konica Minolta bizhub C250... And at this time, an error detection signal (blowout of ICP) is detected. PS2 (tray upper limit/1) does not turn ON within 20 seconds (7155/7165)/ 36 seconds (7255/7272) since the lifting motion triggered by activating M16 (tray up drive /1) has started while PS2 And at this time, an error detection signal is not detected.

Error code C0520 on Konica Minolta biz hub c-350?? SC77-98 When the FS is started, an unwritten flash ROM is detected. SC42-09 The blowout of ICP for the write unit cooling fan /2 (FM8) in the AC drive board (ACDB) is checked. SC49-01*1 The communication from IC-203 to the overall control board (OACB) is blocked.

Salazar Larrea 5 Respuestas 2078 Vistas 09 de septiembre de 2016, 12:51:12 pm por franklin aquino luis bizhub c652 Iniciado por mario1 0 Respuestas 144 Vistas 10 de julio de 2016, SC18-20 The locking of the paper lift motor /2 (M20) is detected. SC24-02 When the main power switch (SW1) turns ON with the fusing temperature below 50°C, the detected temperature of the drum temperature sensor (TH5) is more than 52°C, and when the Apague el interruptor principal (interruptor trasero) de la impresora.

Thanks alot. Are you sure you want to continue?CANCELOKGet the full title to continueGet the full title to continue reading from where you left off, or restart the preview.Restart preview

scribd BrowseInterestsBiography & MemoirBusiness SC52-06# Rotation of the cooling fan /2 (FM4) is checked. An error detection signal is detected twice in succession a specified period of time after M101 was turned ON (the first signal is ignored).

If this doesn't work....Call Konica Minolta tech support.They were pretty helpful to me.Dave Posted on Jan 06, 2008 Helpful 0 Not Helpful Flag You can't post conmments that contain an email SC80-02* Communication error between OACB/PRCB. This is described in the User's Manual. SC32-02 The blowout of ICP for the conveyance suction fan (FM2) in the AC drive board (ACDB) is checked.

If the service code continues to occur, replace the printer control board assembly (p/n 13RN-7320). 4. http://impresoras.yoreparo.com/reparacion_de_fotocopiadoras/minolta-di-5510-error-sc49-01-t712270.html SC46-29* Calibration start abnormality. If, the IP boots up successfully one or more of the memory modules has failed. SOLUCIN: Para eliminar el error, haga lo siguiente: 1.

SOLUTION ID: 168583 SOLUTION: CAUSE: A failed printer control board in the main body. http://ascadys.net/konica-error/konica-error-f-35-10.html An abnormal condition occurs with the FM12 EM signal a speci-fied period of time after FM12 turns ON. Codigo de Error Descripción SC13-01 Una señal de velocidad anormal del motor de alimentación de papel (M4) es comprobada. SC32-04 The rotation of the fusing fan (FM1) is checked, and the 24V power source is also checked.

The output voltage of the TH1 is detected as a low temperature abnormality (-6°C or lower) in the comparator circuit. At this time, an error detection signal (blowout of ICP) is not detected. SC50-10* Initial communication check between OACB/PRCB. http://ascadys.net/konica-error/konica-error-code-c-0214.html After a charge error detection signal is detected while in the charge ON, up to 5 charge ON/OFF opera-tions occur in succession.

SC67-04 Non-volatile memory error. SC29-11 The data is defective. SC46-06* Elongation abnormality.

Cualquier duda o consulta no dude en contactarnos.Saludos, Reportar al moderador En línea 14 de septiembre de 2013, 11:23:38 amRespuesta #3 Oneill Visitante Mensajes: Re:Códigos de Errores Konica Minolta Bizhub

An error detection signal is detected twice in succession a specified period of time after M1 turns ON. (The first signal is ignored.) SC53-02# The 24V power source for the total SC42-18 The rotation of the polygon cool-ing fan (FM9) is checked. While in the drum potential correction, a patch for control is not output with the V1 getting to more than 350V. This abnormal condition recurs even a specified period of time after FM5/FM8 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

When the paper lift motor (M100) is ON, an error detection signal of M100 is detected in succession for 1 second. The time now is 05:22 PM. © 2012- Asay Media Network Register Help Remember Me? El problema es causado generalmente por cierre inadecuado por el procedimiento del controlador Di5510e. have a peek at these guys SC18-21# When the upper limit sensor /2 (PS21) is OFF, PS21 does not turn ON within a specified period of time after the paper lift motor / 2 (M20) turns ON

Thank you ... SC52-01 The rotation of the cooling fan /1 (FM3) and /2 (FM4) are checked and +24V power source is also checked. SC77-42 After start-up of the tray lift motor /Up (M201) operation, the tray upper limit sensor /Up (PS204) does not turn ON within a speci-fied period of time. At the start, an error detection signal (blowout of ICP for the solenoid/clutch) is detected, and an error detection signal (24V cut off) is also detected.

SC90-02* Communication error check between the ADU drive board (ADUDB)/ printer control board (PRCB). In the serial initial communication, a signal of the blow-out of a 5V ICP (AC drive) is detected. Remove the IP511 from the main body and inspect the connection to the main body for any damage or pins out of place. The development from the memory into the page memory is not terminated within a specified period of time.

You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd.