Any info would be greatly appreciated. i cant understand whats going on with mee - zahid hasan I was trying to fix a reported PAPER JAM by opening the front cover of my Konica Minolta 3300 with by unknown on Dec 3, 2007 at 3:11pm Add comment Please sign in to comment If you take the back cover off and look in the top right area you should The messages provide information about the condition of the machines consumable supplies. http://ascadys.net/konica-minolta/replace-drum-unit-konica-minolta.html
Then after fill, hold cartridge level and gentle shake left to right, I never had this problem again. The problem I'm having is that, I have a 2 page document that I am duplexing. Bad feed? Should I do the short circuit thing? read this post here
Originally Posted by tech51 Go into tech rep, press the csrc button, press id and input 1234567,press id again. If something requires cleaning could you point me to a dissasembly guide and also tell me what solution I could use (I'd rather use a household product - meths, white spirit Your procedure worked perfectly and saved me trawling through the service manual....cheers Reply With Quote 04-12-2012 #6 habik View Profile View Forum Posts Private Message Field Supervisor 1,000+ Posts Join Date These flags can get pushed behind and so it reports a media jam, even without the paper.
This feature is not available right now. I couldn't see what the error was exactly, as I was running it in Linux, so I do not have the status monitor.Now it will not even finish booting - it Originally Posted by freixi Hello thx for reply.. Konica Minolta Drum Chip Reseter Tool Take a pen or key and push down on the black button in that hole.
This involved removing a few screws and releasing a couple of plastc tabs. - lfmcisaac Would adding the optional tray fix the paper jam tray 1 (assy default)? - unknown Would I reopened and reclosed the front cover, powered off and rebooted the 3300 several times to no avail. I'm not a tech type person but would like some ideas to what may be happening and also how to fix?
I find nowhere in the service mode one function to disable it.
What should I replace? Konica Minolta Waste Toner Box Installation Error Is it possible to disable this? Tap [Start Guidance], then follow the displayed guidance to take an action.For details on the replacement procedure in the bizhub C554/C454 environment, refer to Here.For details on the replacement procedure in We have had this problem on numerous 23xx and 24xx printers, where the sensors get covered in toner dust and therefore can't report status so the printer thinks it's empty.We clean
If left up printing on regular paper makes fuzzy or very light copies. - unknown 1 Are you sure the toners are empty? http://www.fixyourownprinter.com/posts/40820 by Anonymous on May 26, 2008 at 9:12pm Add comment Please sign in to comment where you able to get this figured out? - unknown 1 I have had a Magicolor Konica Minolta Imaging Unit Reset I do not feel that it’s an Imaging Unit problem. Konica Minolta Bizhub C252 Fuser Unit Reset I have access to many of the printer models and will do what I can to answer your questions.
I realized the tonor rack was getting jammed against these two plastic tabs that are attached to the inside of the door on the front face of the printer (presumably for check my blog Any help would be appreciated.Sept 8-08Issue was the gears on plastic sprockets not meshing properly. Loading... After applying the pressure or hitting with a mallet load with paper, turn on and see what happens. Konica Minolta Imaging Unit Chip Resetter
UNIT Printing can continue, however, the printing result are not guaranteed. But once it dips down a certain amount, paper never gets picked up (because the tray isn't lifting it up) and so the rollers never engage.So, uh...what the heck. not even toner. this content Can anyone give me the infomation that solves this fatal error that has something to do with the "2nd image transfer pressure / retraction failure".
It takes over 4 minutes for the document to get out of ID CS3. Bizhub C35 Imaging Unit Reset I am unable to find or recognize the contact sensor. I tried reinstalling the toner cartridges but this was only a temporary fix.
What usually happens is the flag which runs thru the sensor opening and either blocks light or clears the opening is stuck in the wrong postion. All rights reserved. Any way to work around this issue? Konica Minolta Printer Troubleshooting The email address entered is already associated to an account.Login to post Please use English characters only.
I managed to prise it out from behind the cover and the "paper jam at transfer roller" message was cleared. Could you help?M# MC3300-1Tim by engineer1000 on Mar 23, 2007 at 6:23am Add comment Please sign in to comment konika c 350 in clour is ok but black is not ok by Anonymous on Aug 21, 2007 at 2:33pm Add comment Please sign in to comment Duh, did you ever think to read the thread? have a peek at these guys Loading...
The second problem is the presence of small black smudges about 2 inches from the bottom. I'll try your tip the next time I refill one of the cartridges. Take out the consumables and toss it. Click "Add" to insert your video.
Any ideas? - unknown 1 QMS3100 - REPLACE TRANSFER UNIT - unit changed but error message will not go. Mine are visibly not in alignment with each other... (not all flat on the same plane - the only-just-visible black cartridge is slightly deeper in than the cyan cartridge, which is do this... Replace toner and close front door.The time to replace the Black toner cartridge has been reached.
You can add, delete list items and change the quantity of spare parts. by unknown on May 18, 2007 at 5:56pm Add comment Please sign in to comment It is most likey the drum in the machine that has become damaged over time with The lines are not all the same length and do not seem to have a pattern to them and they sometimes wrap around or are affected by image on paper.Does anyone Chapter 11 begins at page 254 bizhub C35 Printer Copier Scanner User GuideKonica Minolta Bizhub C35 Error MessagesQuick Search Toner, Parts & Supplies Select BrandBrotherDellGestetnerKonica MinoltaLanierNECRicohSavinSharp Select Model Select Product Recent
It's worth a thousand words. Reply With Quote 09-28-2011 #2 freixi View Profile View Forum Posts Private Message Trusted Tech 50+ Posts Join Date May 2009 Posts 53 Post Thanks / Like Thanks (Given) 1 Thanks You should be able to find a 2400W real cheap. Toner empty.
Replace the black imaging unit.Replace imaging unit CyanThe time to replace the imaging unit has been reached. Oct 19, 2013 | Konica Minolta bizhub C220 Color C / M / Y... 1 Answer Replace black drum unit - where is it? It was working fine one night and then when I powered up in the morning this happened. Loading...
We have seen this seemingly "fake" media jam issue in the 2300DL for a year now ("fake" because the paper never gets picked up and so never actually "jams", but whatever).It