Home > Konica Minolta > The Adf Is Currently Not Available Konica Minolta

The Adf Is Currently Not Available Konica Minolta


It's been really good printing good quality photos and everything. Reply With Quote 06-30-2011 #4 zaza View Profile View Forum Posts Private Message MECANOGRAPHE 1,000+ Posts Join Date Mar 2008 Location ALGERIA Posts 1,081 Post Thanks / Like Thanks (Given) 4 My machine was automatically turned off and when I turn it on, the duplex functions was deactivated because ADF was not working. These levers reduce fuser pressure, and if theyare in the up position (i.e. http://ascadys.net/konica-minolta/konica-minolta-won-39-t-print.html

It looked almost impossible to get them out without damage so I just shorted across the plates with a single core wire stiff enough to secure it. The top one is very high (easy to miss), but the lower one was my problem, with it sticking behind the hole. I will try it out and let you know if that was the issue. by tomhplshelp on Apr 25, 2011 at 11:55am Add comment Please sign in to comment 1 I am working on an K/M magic color 3300 that instead of getting a shaded http://manuals.konicaminolta.eu/bizhub-C554-C454-C364-C284-C224/EN/contents/id16-0201.html

The Adf Is Currently Not Available Konica Minolta

To do this, enter service mode (Utility, Stop, 0,0,Stop,0,1) and search through the listings for the clear function. If the pin is not in the groove then the unit will draw paper just though the fuser unit then report a jam. My assumption is that there is dirt on the sensor, but I don't know where it is. My machine was automatically turned off and when I turn it on, the duplex functions was deactivated because ADF was not working.

Printer Repair in Salt Lake City, Utah, YP.* 5211 South Green Pine Drive Murray, UT 84123 * USA *Office:(801)506.0277 *Copyright© Office Imaging Systems 2004, All rights reserved. I realized the tonor rack was getting jammed against these two plastic tabs that are attached to the inside of the door on the front face of the printer (presumably for PS I have service manual, but do not see anything in troubleshooting section pertaining to this problem.Sincerely, Magna by unknown on Oct 23, 2007 at 7:08pm Add comment Please sign in Konica Minolta Bizhub C451 Paper Jam This involved removing a few screws and releasing a couple of plastc tabs. - lfmcisaac Would adding the optional tray fix the paper jam tray 1 (assy default)? - unknown Would

The problem I'm having is that, I have a 2 page document that I am duplexing. Konica Minolta Keeps Jamming Figure : Example of the parts on an ADF ADF cover Rollers Separator pad Clean the separator pad using the same cloth. by unknown on May 31, 2007 at 11:41am Add comment Please sign in to comment I had a similar problem on a clinet 2430DL printing fuzzy or very light. It kind of looks like multicolored barcode from top to bottom of page with all the lines extending from left edge in about 1/2 - 3/4".

We try to unpause it and it immediately goes back to Paused. Konica Minolta Paper Jam It has about 65000 images printed. Then more recently, the paper would come 1/2 way out of the printer and stop and "Jam" would read on the display. I'm tired of this!

Konica Minolta Keeps Jamming

We have had this problem on numerous 23xx and 24xx printers, where the sensors get covered in toner dust and therefore can't report status so the printer thinks it's empty.We clean Pull the plate in the direction the springs allow it to go about a half inch then allow it to snap back into place. The Adf Is Currently Not Available Konica Minolta note: Do not fan the paper by running your fingers through the paper stack. Konica Minolta Adf Not Available hello ..tell me friend TOP ..if you started this machine ..it have any error code ?...l think you should be have the isw and frimware for this konica minolta 7085 ...l

How does HP install software and gather data? check my blog Remove paper according to the instructions.]Copying cannot be performed due to a paper jam.Follow the guidance (instructions) to remove jammed paper.[Hole-Punch scrap box is full. But has occasionally on power off and power on stopped for a short time.Since the problem has gone away at times, then I assume it is not drum or toner related. Make certain both green levers are down and you can seethe envelop icons. Konica Minolta Bizhub Adf Not Available

I tried the obvious solutions (replacing the cartage, turning it off for a few minutes etc). I have yet use the origional toners which are the partially full ones. I tried to clean the cleaner parts above the drum, but didn't work. this content Replace the Toner Cartridge according to the instructions.]Toner is depleted.According to the maintenance agreement, replace Toner Cartridge. [No more staples.

Tried disconnecting from network and removing paper trays but no effect. Konica Minolta Bizhub 164 Paper Jam And since it has happened to both machines then I thought this may be a common problem that someone might have experienced. Contacting HP for service in all countries/regions except Asia Pacific.

It does not jam when printing black and white, however the image still shifts.

The source of your refill toner should have supplied a new chip - it would probably be in a small bubble plastic bag. My 2400w was blinking the error light steadily (even after restarting it -- green ready would come on briefly, then yellow blinking error again) as if there was a paper jam How can I do for it? Konica Minolta Paper Jam Troubleshooting not even toner.

It has about 9,000 faces, 5788 color, and 25,000 planes on it. by S.Smith on May 9, 2016 at 12:07pm Add comment Please sign in to comment 0 Hi!I have KM Pagepro 1300W printer, and prints dirty pages.I tried to print with another I'm no printer tech, but in most other lasers (HPs, etc) the paper tray lifts, or pushes up a little on the paper stack, via springs, coils, or other mechanical means. have a peek at these guys The machine are not running.

i cant understand whats going on with mee - zahid hasan hi... Good luck . However, I have seen in the manual, in the section about how to disassemble absolutely everything, that the toner cartridges can be rotated manually.